|
Post by Frank on Nov 7, 2014 18:58:29 GMT 10
Since I've had the bike (a couple of years now) I've thought that the handlebars may have been adjusted for the last owner. Looking at the side on I would like to adjust them a little further forward so that they are almost in a straight line with the forks but, the bolts that hold the head stem have covers on them which are round, I don't want to bugger those up.
Can someone please tell me how are bolt covers removed to access the bolts?
|
|
|
Post by Azza ( AB ) on Nov 7, 2014 20:41:10 GMT 10
Hey Frank they a simple push in plug that will pop out with out much difficulty just get a very fine small screw driver or pocket knife and gently ease them up by working the tip of the knife in under the edge of the cap. A good ergonomic position to help reduce fatigue is to set your bars so that your forearms are parallel with the ground when sitting on the bike in your riding position. Azza
|
|
|
Post by mh (Steve) on Nov 7, 2014 21:59:55 GMT 10
Great question and great answer, thanks guys I was wondering the same thing. Now have a job for the weekend.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Nov 8, 2014 6:11:04 GMT 10
I lifted mine a little, its amazing how much such a small change can do to make it more comfortable.
|
|
|
Post by sheepdog on Nov 8, 2014 11:50:47 GMT 10
Make sure you cover yourr tank with a couple of towells etc? Just in case you happen to haveca little bit of trouble getting the mbars exactly where you need them? Could also get a bungee to hold your front wheel exactly straight and in the one position.
|
|
|
Post by rodaco on Nov 8, 2014 13:10:07 GMT 10
I guess it depends what model/year your bike is. My handle bars are welded to the risers and no adjustment is possible. I know in some cases people have bought different risers and carefully ground the old risers off and fitted the clamp type. Some choose to fit different length/angle risers so as to get some "pullback" on the bars. Rodaco.
|
|
|
Post by sheepdog on Nov 8, 2014 19:37:12 GMT 10
Just a side note? That welded bars are supposedly not legal in Australia. As mine are welded bars as well. I will say this only once and completely and utterly deny all knowledge
|
|
|
Post by rodaco on Nov 8, 2014 21:02:52 GMT 10
Just a side note? That welded bars are supposedly not legal in Australia. As mine are welded bars as well. I will say this only once and completely and utterly deny all knowledge Well now you've opened a can of worms! There must be a lot of bikes out there just like that.
|
|
|
Post by rodaco on Nov 8, 2014 21:34:02 GMT 10
Well, I just checked the Queensland Transport website in relation to Roadworthy Inspections, and they only mention that welding REPAIRS or heat treatment to motorcycle handlebars are not legal.
|
|
|
Post by Frank on Nov 8, 2014 22:02:00 GMT 10
Hey Frank they a simple push in plug that will pop out with out much difficulty just get a very fine small screw driver or pocket knife and gently ease them up by working the tip of the knife in under the edge of the cap. A good ergonomic position to help reduce fatigue is to set your bars so that your forearms are parallel with the ground when sitting on the bike in your riding position. Azza Thanks for that, I'll give it a go tomorrow
|
|
|
Post by bdrgonzo on Nov 9, 2014 6:05:52 GMT 10
I changed my bars completely with some 14 inch apes. I know it's more than just the simple repositioning, but damn it has made the bike fit me and therefor more comfortable. Matched with the 4inch forward controls and I have a lounge chair with wheels and a motor.
|
|
|
Post by Frank on Nov 10, 2014 20:15:32 GMT 10
Thanks you all, done and feels lots better
|
|
Steve
Scout
2012 Honda Shadow VT750C
Posts: 197
|
Post by Steve on Nov 11, 2014 16:26:31 GMT 10
Hey Frank they a simple push in plug that will pop out with out much difficulty just get a very fine small screw driver or pocket knife and gently ease them up by working the tip of the knife in under the edge of the cap. A good ergonomic position to help reduce fatigue is to set your bars so that your forearms are parallel with the ground when sitting on the bike in your riding position. Azza Thanks Azza, good point, I will check my forearm position on the weekend
|
|